RS3000 (VIP)

 

DEALER FITTED REMOTE KEYLESS ENTRY PROGRAMMING

 

NOTE : Maximum of 8 remote transmitters can be programmed.

 

NOTE : From 1998 MY the remote transmitters were updated from BLACK to GREY. The new GREY remote transmitters will not work on the older vehicles.

 

ADD REMOTE TRANSMITTER

 

1.    Locate the RS3000 ECU.

 

The ECU locations are as follows :

 

            4runner(1999MY) : Behind panel right hand side of steering wheel, older models under drivers seat.

            Avalon : Under passenger seat.

            Camry (1998/1999MY) Older models located under drivers seat.

            Celica : Under drivers seat.

            Corolla : Under drivers seat.

            RAV4 : Under drivers seat.

            Sienna : Behind panel right hand side of steering wheel.

            Solara : Centre console in storage compartment.

            T100 : Under drivers seat.

            Tacoma : Under drivers seat.

            Tercal : Under drivers seat.

 

2.    Insert ignition key, and turn ON.

3.    PRESS and HOLD the ECU PROGRAMMING SWITCH for 3 seconds (Located on the side of the ECU)

 

NOTE : The STATUS MONITOR LED will light for 5 seconds.

 

NOTE : Please perform the next step within 5 seconds.

 

4.    PRESS and release either button on the remote transmitter.

 

NOTE : The STATUS MONITOR LED will turn OFF and the sounder will sound once.

 

5.    Turn OFF the ignition, the remote transmitter is now programmed.

 

ERASE ALL REMOTE TRANSMITTERS

 

1.    Insert ignition key, and turn ON.

 

2.    PRESS and HOLD the ECU PROGRAMMING SWITCH for 3 seconds (Located on the side of the ECU)

 

NOTE : The STATUS MONITOR LED will light for 5 seconds.

 

NOTE : Please perform the next step within 5 seconds.

 

3.    PRESS and HOLD the ECU PROGRAMMING SWITCH for 3 seconds.

 

NOTE : The STATUS MONITOR LED will flash 3 times, and the sounder will sound 3 times.

 

4.    Turn ignition OFF, all remote transmitters are now erased.

 

RS3200

 

DEALER FITTED REMOTE KEYLESS ENTRY PROGRAMMING

 

 

RS3200 (TVIP)

 

DEALER FITTED REMOTE KEYLESS ENTRY PROGRAMMING

 

NOTE : Maximum of 4 remote transmitters can be programmed.

 

NOTE : When a new remote transmitter it will be programmed in normal mode, additional options for this system

can be setup by referring to the main operating manual of this system.

 

1.    Open the drivers door and remove the ignition key.

 

2.    The programming steps must be performed within 40 seconds.

 

3.    Insert the key into the ignition 2 times.

 

4.    Close then open the drivers door 2 times.

 

5.    Insert the key into the ignition 1 time.

 

6.    Close then open the drivers door 2 times.

 

7.    Insert the key into the ignition and leave it in.

 

8.    Close the drivers door.

 

9.    Turn the ignition key from LOCK to ON, and then back to LOCK position.

 

10. Remove the key.

 

11. The tail/rear lights will flash once, the sounder will sound once and the doors will LOCK and UNLOCK.

 

12. Press the LOCK and UNLOCK button once together on the remote transmitter to be programmed.

 

13. Press the LOCK button on the remote transmitter.

 

14. The tail/rear lights will flash once, the sounder will sound once and the doors will LOCK and UNLOCK.

 

15. Repeat steps 12 to 14 for any additional remote transmitters.

 

16. Open the drivers door.

 

TO ERASE AND PROGRAM EXISTING REMOTE TRANSMIITERS

 

1.    Open the drivers door and remove the ignition key.

 

2.    The programming steps must be performed within 40 seconds.

 

3.    Insert the key into the ignition 2 times.

 

4.    Close then open the drivers door 2 times.

 

5.    Insert the key into the ignition 1 time.

 

6.    Close then open the drivers door 2 times.

 

7.    Insert the key into the ignition and leave it in.

 

8.    Close the drivers door.

 

9.    Turn the ignition key from LOCK to ON, and then back to LOCK position 2 times.

 

10.  REMOVE the key.

 

11.  The tail/rear lights will flash once, the sounder will sound once and the doors will LOCK and UNLOCK.

 

12.  PRESS the LOCK and UNLOCK button once together on the remote transmitter to be programmed.

 

13.  PRESS the LOCK button on the remote transmitter.

 

14.  The tail/rear lights will flash once, the sounder will sound once and the doors will LOCK and UNLOCK.

 

15.  Repeat steps 12 to 14 for any additional remote transmitters.

 

16.  OPEN the drivers door.

 

17.  LOCK and UNLOCK the doors using the drivers door LOCK button 5 times.

 

18.  Insert key into ignition and turn to the ON position 2 times, then remove the key.

 

19.  LOCKS should cycle from LOCK to UNLOCK to confirm programming.

 

20.  Press the LOCK and UNLOCK button together on the remote transmitter for 1 second.

 

21. The LOCKS should cycle LOCK to UNLOCK to confirm programming.